Jump to content

I give up.

Todd Holley

By Todd Holley
in Off-Topic

Recommended Posts

  • Replies 62
  • Created
  • Last Reply
Todd Holley Super Member

Todd Holley

Posted
  • Author
Posted

Well jus tto tell everyone, we have fixed it. And it wasn't a problem on my side. A nice competitor gsp had a program flooding out servers on my master servers ip address.

 

ECF-- This guy is registered on these forums. Do what you please.

 

 

Thank you all for your help. And especially Jissh!

Link to comment
Share on other sites
ECF Super Member

ECF

Posted
Posted
ECF-- This guy is registered on these forums (lowpinggaming). Do what you please

 

While I personally would not condone such behavior, unless someone breaks our forum rules there is little that we can do about their forum account.

 

If you can show proof that said person did this to your system I would suggest contacting their service provider about it?

Link to comment
Share on other sites
Jissh Super Member

Jissh

Posted
Posted
That mod you sent me will not upload. This is the error i get in tcadmin console,

 

httpfilwupload.start: Index was out of range. Must be no n-negative and less than the size of the collection

?

 

Not sure about the error (Probly just TCA blocking it by default). Have you tried uploading it via the FTP server?

Link to comment
Share on other sites
Todd Holley Super Member

Todd Holley

Posted
  • Author
Posted

I am about to just load it into my cod files in /GameInstalls/ So it will be there no matter what. Can I just put that file in there and use set scr_awe_showlogo 1 ? Without any other awe files?

 

 

==============

 

 

And the only way I could prove it was if there was a program that monitored connections to your box. (Like what ip's). Then I could make sure he is the one doing it.

Link to comment
Share on other sites
HIS-MOTHER Super Member

HIS-MOTHER

Posted
Posted

 

And the only way I could prove it was if there was a program that monitored connections to your box. (Like what ip's). Then I could make sure he is the one doing it.

 

 

So you accused without proof? LOL

 

Try a firewall as it logs all IP's and blocks any incoming flooding if that is in fact what was causing your issue. ;)

Link to comment
Share on other sites
ECF Super Member

ECF

Posted
Posted 
NETSTAT [-a] [-b] [-e] [-n] [-o] [-p proto] [-r] [-s] [-v] [interval]
 -a            Displays all connections and listening ports.
 -b            Displays the executable involved in creating each connection or
               listening port. In some cases well-known executables host
               multiple independent components, and in these cases the
               sequence of components involved in creating the connection
               or listening port is displayed. In this case the executable
               name is in [] at the bottom, on top is the component it called,
               and so forth until TCP/IP was reached. Note that this option
               can be time-consuming and will fail unless you have sufficient
               permissions.
 -e            Displays Ethernet statistics. This may be combined with the -s
               option.
 -n            Displays addresses and port numbers in numerical form.
 -o            Displays the owning process ID associated with each connection.
 -p proto      Shows connections for the protocol specified by proto; proto
               may be any of: TCP, UDP, TCPv6, or UDPv6.  If used with the -s
               option to display per-protocol statistics, proto may be any of:
               IP, IPv6, ICMP, ICMPv6, TCP, TCPv6, UDP, or UDPv6.
 -r            Displays the routing table.
 -s            Displays per-protocol statistics.  By default, statistics are
               shown for IP, IPv6, ICMP, ICMPv6, TCP, TCPv6, UDP, and UDPv6;
               the -p option may be used to specify a subset of the default.
 -v            When used in conjunction with -b, will display sequence of
               components involved in creating the connection or listening
               port for all executables.
 interval      Redisplays selected statistics, pausing interval seconds
               between each display.  Press CTRL+C to stop redisplaying
               statistics.  If omitted, netstat will print the current
               configuration information once.

Link to comment
Share on other sites
Todd Holley Super Member

Todd Holley

Posted
  • Author
Posted
So you accused without proof? LOL

 

Try a firewall as it logs all IP's and blocks any incoming flooding if that is in fact what was causing your issue. ;)

 

 

Well what a coincidence, after I took about 8 or 9 of his customers I got a friendly email and the next morning everything started happening.

 

 

======================================

 

 

 

And now, I am having errors with my box after I replied to the email. (conincidence?). I can not even rdc my server. So I will install netstat asap.

Link to comment
Share on other sites
Todd Holley Super Member

Todd Holley

Posted
  • Author
Posted

lol... If he is doing all this, which I am pretty sure he is. I don't know why he would. Competition does 2 things, kills you or makes you a better company. He overloads his servers and has lagg and horrible support. Why not watch me make mistakes so he can avoid them? And in call of duty 1.3 there is only 1 host, HIM. People need choices. I am 50 cents a slot higher than him. Only for better support and pings in the 40's. I honestly do not understand any of this. All I want to do is make a few bucks being a GSP. And he wants to completely prevent that.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Who's Online   0 Members, 0 Anonymous, 8 Guests (See full list)

    • There are no registered users currently online
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. Terms of Use